XPON 1G1F+WIFI+CATV Chinese Suppliers
Overview
●1G1F+WIFI+CATV is designed as HGU (Home Gateway Unit) in transfer data FTTH solutions; the carrier-class FTTH application provides data service access.
● 1G1F+WIFI+CATV is based on mature and stable, cost-effective XPON technology. It can switch automatically with EPON and GPON mode when it access to the EPON OLT or GPON OLT.
● 1G1F+WIFI+CATV adopts high reliability, easy management, configuration flexibility and good quality of service (QoS) guarantees to meet the technical performance of the module of China telecommunications EPON CTC3.0.
● 1G1F+WIFI+CATV is compliant with IEEE802.11n STD, adopts with 2x2 MIMO, the highest rate up to 300Mbps.
● 1G1F+WIFI+CATV is full compliant with technical regulations such as ITU-T G.984.x and IEEE802.3ah.
● 1G1F+WIFI+CATV is compatible with PON and routing. In routing mode, LAN1 is the WAN uplink interface.
● 1G1F+WIFI+CATV is designed by Realtek chipset 9602C.
Feature
> Supports Dual Mode (can access GPON/EPON OLT).
> Supports GPON G.984/G.988 standards
> Support CATV interface for Video Service and remote control by Major OLT
> Support 802.11n WIFI (2x2 MIMO) function
> Support NAT, Firewall function.
> Support Flow & Storm Control , Loop Detection, Port Forwarding and Loop-Detect
> Support port mode of VLAN configuration
> Support LAN IP and DHCP Server configuration.
> Support TR069 Remote Configuration and maintenance.
> Support Route PPPOE/IPOE/DHCP/Static IP and Bridge mixed mode.
> Support IPv4/IPv6 dual stack.
> Support IGMP transparent/snooping/proxy.
> Support PON and routing compatibility function.
> In compliant with IEEE802.3ah standard.
> Compatible with popular OLT (HW, ZTE, FiberHome,VSOL...)
Specification
|
Technical Item |
Details |
| PON interface |
1 G/EPON port(EPON PX20+ and GPON Class B+) Upstream: 1310nm; Downstream: 1490nm SC/APC connector Receiving sensitivity: ≤-28dBm Transmitting optical power: 0~+5dBm Transmission distance: 20KM |
| LAN interface |
1x10/100/1000Mbps and 1x10/100Mbps auto adaptive Ethernet interfaces. Full/Half, RJ45 connector |
| WIFI Interface |
Compliant with IEEE802.11b/g/n Operating frequency: 2.400-2.4835GHz support MIMO, rate up to 300Mbps 2T2R,2 external antenna 5dBi Support: Multiple SSID Channel:13 Modulation type: DSSS、CCK and OFDM Encoding scheme: BPSK、QPSK、16QAM and 64QAM |
| CATV Interface |
RF, optical power : +2~-15dBm Optical reflection loss: ≥45dB Optical receiving wavelength: 1550±10nm RF frequency range: 47~1000MHz, RF output impedance: 75Ω RF output level: ≥ 80dBuV（-7dBm optical input） AGC range: +2~-7dBm/-4~-13dBm/-5~-14dBm MER: ≥32dB(-14dBm optical input), ＞35(-10dBm) |
| LED |
9 LED, For Status of WIFI、WPS、PWR、LOS、PON、LAN1~LAN2、 WORN、 NORMAL(CATV) |
| Push-Button |
4, for Function of Power on/off, Reset, WPS, WIFI |
| Operating condition |
Temperature : 0℃～+50℃ Humidity :10%～90%（non-condensing） |
| Storing Condition |
Temperature : -40℃～+60℃ Humidity :10%～90%（non-condensing） |
| Power supply |
DC 12V/1A |
| Power Consumption |
<6W |
| Net Weight |
<0.4kg |
Panel lights and Introduction
|
PilotLamp |
Status |
Description |
|
WIFI |
On |
The WIFI interface is up. |
|
Blink |
The WIFI interface is sending or/and receiving data (ACT). |
|
|
Off |
The WIFI interface is down. |
|
|
WPS |
Blink |
The WIFI interface is securely establishing a connection. |
|
Off |
The WIFI interface does not establish a secure connection. |
|
|
PWR |
On |
The device is powered up. |
|
Off |
The device is powered down. |
|
|
LOS |
Blink |
The device doses not receive optical signals or with low signals. |
|
Off |
The device has received optical signal. |
|
|
PON |
On |
The device has registered to the PON system. |
|
Blink |
The device is registering the PON system. |
|
|
Off |
The device registration is incorrect. |
|
|
LAN1~LAN2 |
On |
Port (LANx) is connected properly (LINK). |
|
Blink |
Port (LANx) is sending or/and receiving data (ACT). |
|
|
Off |
Port (LANx) connection exception or not connected. |
|
|
WARN (CATV) |
On |
Input optical power is higher than 2dBm or lower than -15dBm |
|
Off |
Input optical power is between -15dBm and 2dBm |
|
|
Normal (CATV) |
On |
Input optical power is between -15dBm and 2dBm |
|
Off |
Input optical power is higher than 2dBm or lower than -15dBm |
Schematic diagram
● Typical Solution：FTTO(Office)、 FTTB(Building)、FTTH(Home)
● Typical Service：Broadband Internet access, IPTV, VOD(video on demand), video surveillance, etc.
Product Picture
Ordering information
|
Product Name |
Product Model |
Descriptions |
|
XPON 1G1F+WIFI+CATV ONU
|
CX21020R02C |
1*10/100/1000M and 1*10/100M Ethernet interface, 1 PON interface, built-in FWDM, 1 RF interface, support Wi-Fi function, support AGC, plastic casing, external power supply adapter |
Basic Configuration Basic Information
"Device Menu" displays the basic information of the current device, such as device name, GPON SN hardware and software version, IP address of LAN, MAC address and connection status of WAN.
NOTE: Some device information may vary by manufacturer.
FAQ
Q1. What is the specification of XPON ONU?
A: XPON ONU has one 10M/100M/1000M and one 10M/100M port, and one WIFI CATV port. Support adaptive GPON and EPON mode, WIFI complies with IEEE802.11n standard, the maximum rate is 300Mbps. It also has AGC automatic gain function of CATV, and remote management function.
Q2. How does XPON ONU comply with technical specifications?
A: XPON ONU fully complies with technical specifications such as ITU-T G.984.x. It ensures compatibility and interoperability with other network devices that follow the same standards.
Q3. Can the ONU terminal perform remote fault diagnosis and positioning?
A: Yes, the ONU terminal can be used together with the OLT local terminal to realize remote fault diagnosis and location. This allows efficient troubleshooting and problem solving without physical intervention.
Q4. What commands can be issued using TR069 OMCI?
A: XPON ONU supports TR069 OMCI command, which can be used for configuration management, software upgrade, performance monitoring and other purposes. These commands provide a standardized method for remote management and control of ONUs.
Q5. Which OLT brands are compatible with XPON ONU?
A: XPON ONU is compatible with SMART OLT, UP2000, Huawei, ZTE, Fiberhome, CDATA, VSOL, HSGQ, BDCOM and other OLT brands. This ensures flexibility and interoperability with different network infrastructures
